Q235B Steel

49 cfr 192 283 plastic pipequalifying joining

49 cfr 192 283 plastic pipequalifying joining

49 cfr 192 283 plastic pipequalifying joining

§191.27 49 CFR Ch. I (10111 Edition)

192.279 Copper pipe. 192.281 Plastic pipe. 192.283 Plastic pipe:Qualifying joining pro-cedures. 192.285 Plastic pipe:Qualifying persons to make joints. 192.287 Plastic pipe:Inspection of joints. Subpart GGeneral Construction Require-ments for Transmission Lines and Mains 192.301 Scope. 192.303 Compliance with specifications or standards. » 49 CFR 192.285 Plastic pipe:Qualifying persons to Terms Used In 49 CFR 192.285. May:means "is permitted to" or "is authorized to".See 49 CFR 192.15; Operator:means a person who engages in the transportation of gas.See 49 CFR 192.3; Person:means any individual, firm, joint venture, partnership, corporation, association, State, municipality, cooperative association, or joint stock association, and including any trustee, receiver, assignee

49 CFR § 192.281 - Plastic pipe. CFR US Law LII

(1) A butt heat-fusion joint must be joined by a device that holds the heater element square to the ends of the pipe or component, compresses the heated ends together, and holds the pipe in proper alignment in accordance with the appropriate procedure qualified under § 192.283. 49 CFR § 192.285 Plastic pipe:Qualifying persons to make (a) No person may make a plastic pipe joint unless that person has been qualified under the applicable joining procedure by:(1) Appropriate training or experience in the use of the procedure; and 49 CFR § 192.287 - Plastic pipe:Inspection of joints § 192.287 Plastic pipe:Inspection of joints. No person may carry out the inspection of joints in plastic pipes required by §§ 192.273(c) and 192.285(b) unless that person has been qualified by appropriate training or experience in evaluating the acceptability of plastic pipe joints made under the applicable joining procedure.

49 CFR § 192.756 - Joining plastic pipe by heat fusion

Nov 20, 2018 · § 192.756 Joining plastic pipe by heat fusion; equipment maintenance and calibration. Each operator must maintain equipment used in joining plastic pipe in accordance with the manufacturer's recommended practices or with written procedures that have been proven by test and experience to produce acceptable joints. 49 CFR §192 Transportation Of Natural And Other Gas By 192.557 Uprating:Steel pipelines to a pressure that will produce a hoop stress less than 30 percent of SMYS:plastic, cast iron, and ductile iron pipelines. 49:3.1.1.2.8.12 SUBPART L 49 CFR 192.283 - Plastic pipe:Qualifying joining procedures.Dec 12, 2020 · All Titles Title 49 Chapter I Part 192 Subpart F - Joining of Materials Other Than by Welding Collapse to view only § 192.283 - Plastic pipe:Qualifying joining procedures. § 192.271 - Scope. § 192.273 - General.

ASTM F2785 - 18a Standard Specification for Polyamide 12

1.1.1 Pipe and fittings covered by this specification shall not be joined using taper pipe threads. Joining methods qualified in accordance with the requirements of Title 49 CFR Part 192.283 are acceptable. Generic fusion guidelines are given in Appendix X1.Design considerations are discussed in Appendix X2.In-plant quality control programs are specified in Annex A1. Butt Fusion Joining Procedure for Field Joining of It was even more difficult for DOT to enforce the joining requirements in § 192.283 (Plastic pipe, qualifying joining procedures) of the C.F.R. (Code of Federal Regulations) Title 49. Federal Register ::Pipeline Safety:Plastic Pipe RuleRequire PA-12 to comply with the rest of the part 192 requirements related Start Printed Page 29266 to joining, pressure testing, and appurtenances, as detailed in §§ 192.281, 192.283, 192.285, and 192.513.

For future versions of this manual, changes to the

Subpart FJoining of Materials Other Than by Welding 192.271 Scope. 192.273 General. 192.275 Cast iron pipe. 192.277 Ductile iron pipe. 192.279 Copper pipe. 192.281 Plastic pipe. 192.283 Plastic pipe; Qualifying joining procedures. 192.285 Plastic pipe:Qualifying persons to make joints. 192.287 Plastic pipe:Inspection of joints. Generic Butt Fsion Joining Procedure for Field Joining of accordance with the requirements of 49 C.F.R. § 192.283 (Plastic pipe, qualifying joining procedures). Non-destructive ultrasonic inspections and high speed tensile impact testing were also conducted on each fusion combination. Additional testing conducted only on 8 pipe samples, included 176° F (80°C), Interpretation Response PHMSAThis responds to your memo of December 12, 1994, concerning the plastic pipe safety regulations in 49 CFR 192.283 and 192.285. You suggested we amend these regulations to require the use of a joining device in making a sidewall fusion joint.

Pipeline and Hazardous Materials Safety Administration

§192.285 49 CFR Ch. I (10109 Edition) outside the joint area, the procedure qualifies for use. (b) Mechanical joints. Before any writ-ten procedure established under §192.273(b) is used for making mechan-ical plastic pipe joints that are de-signed to withstand Plastic Pipe Final Rule Update - ND PSC § 192.283 Plastic pipe:Qualifying joining procedures. (a)(3) For procedures intended for non -lateral pipe connections, perform testing in accordance with a listed specification. If the test specimen elongates no more than 25% or failure initiates outside the joint area, the procedure qualifies for use Title 49 Part 192 Subpart f - Code of Federal Regulations49 U.S.C. 5103, 60102, 60104, 60108, 60109, 60110, 60113, 60116, 60118, 60137, and 60141; and 49 CFR 1.97. 35 FR 13257, Aug. 19, 1970, unless otherwise noted.

eCFR Code of Federal Regulations

§192.285 Plastic pipe:Qualifying persons to make joints. Link to an amendment published at 84 FR 52245, Oct. 1, 2019. (a) No person may make a plastic pipe joint unless that person has been qualified under the applicable joining procedure by:(1) Appropriate training 49 CFR § 192.283 Plastic pipe:Qualifying joining § 192.283 Plastic pipe:Qualifying joining procedures. (a) Heat fusion, solvent cement, and adhesive joints.

Contact us

Email: [email protected]